
UNIVERSAL RISERS, 7/8`` TUBE TYPE HANDLEBARS, 1`` UP & 1 3/8`` BACK 
The risers replace the stock 7/8" tube type handlebar clampcap to raise the bars up 1" (25mm) and back 1 3/8" (35mm). This will help to relieve wrist and neck pain on long rides. May require some rerouting of control cables, wiring, or hoses. X102B is the black anodized version of X102. Does not fit 1" tube handlebars.


Item no: X102 
Retail: $119.95 
Today's Sale Price: $109.95 




Application Chart 
Diagrams 
Application Notes 

2001 Suzuki DL 1000 VStrom 


2002 Suzuki DL 1000 VStrom 


2003 Suzuki DL 1000 VStrom 


2004 Suzuki DL 1000 VStrom 


2005 Suzuki DL 1000 VStrom 


2006 Suzuki DL 1000 VStrom 


2007 Suzuki DL1000 VStrom 


2002 Suzuki DL650 VStrom 


2003 Suzuki DL650 VStrom 


2004 Suzuki DL650 VStrom 


2005 Suzuki DL650 VStrom 


2006 Suzuki DL650 VStrom 


2007 Suzuki DL650 VStrom 









Fits:
BMW R1150R, 1100GS
Honda
Kawasaki, ZR7 (will require a longer brake hose, not included), ZRX1100
Suzuki, GS500, SV6502003, VStrom
Triumph, Speed Triple, Thunderbird
Yamaha Virago, etc.
X102 installed on a 2002 Suzuki GS500.
X102 riser installed on a Suzuki SV650. Photo courtesy of Scott Shumaker
X102B riser installed on 2002 Honda CB750 Nighthawk (no cable relotion was needed 10 min install)
2002 Honda CB750 Nighthawk (no cable relotion was needed 10 min install). Photo courtesy of Brian Piersol
2002 Honda CB750 Nighthawk (no cable relotion was needed 10 min install). Photo courtesy of Brian Piersol
2002 Honda CB750 Nighthawk (no cable relotion was needed 10 min install). Photo courtesy of Brian Piersol



WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, offroad areas, or race facility areas only. In some states/provinces offroad uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. 

The Q&A on this Product 


QUESTION: Does the center bolt in the x102b go through to the stock holes in where the old ones was ? Thanks again .BP 
ANSWER: Yes, you can't tell from the picture but the center bolt goes through the top cap and riser and then down into your stock riser. There will still be four bolts holding the handlebars down. 

QUESTION: Will the x 102 fit my 1980 yamaha 850 special ? 
ANSWER: The X102 risers will fit a 850 special.


QUESTION: Hi,I have an 2003 XJ 900 Diversion; what will work with my bike with stock cables etc? Thanks Mark

ANSWER: Hi Mark,
Our X102 and X103 style risers will both work on the diversion without any changes to the control cables.
Thank you 

QUESTION: Will any of your kits fit a 2002 Yamaha FZ1000? 
ANSWER: Our X104 risers will fit on the FZ1 with all the stock control cables. Our X102b style risers will fit but a longer brake hose will be required for installation.


QUESTION: 2003 Kawasaki ZRX 1200R. will these work with that and do I need longer cables n such? Thanks 
ANSWER: The X102 risers will work on the ZRX1200R. Because of the way the stock handlebar risers tilt back toward the rider, we recommend the X104 straight up style risers which will give you up 1" and back about 5/8". Because of the angle, the X102 risers will only bring the bars back 1 3/8" and not any upward. You will only need to reroute the throttle cables on the back of the brace that holds the bikini fairing on when installing either riser.


QUESTION: will the x102 fit a 1979 yamaha xs1100 
ANSWER: Our X102 risers will fit the 1979 Yamaha XS1100. 

QUESTION: I have a 2009 Burgman 650 ex scooter What risers will fit it? 
ANSWER: Our X103 risers will fit the 650 but the X102 risers will require some rerouting of the cables. 

QUESTION: Correction...the exact name of the bike is 2001 Kawasaki ZR7S....it's a 750 cc engine. Will the handlebar risers fit? Please advise. Thanks guys. 
ANSWER: Our X102 risers will fit the ZR7S but a longer brake hose will be needed. We currently do not supply the brake hose at this time. 

QUESTION: Will the X102 fit my 05' Suzuki Burgman 650 scooter.

ANSWER: Our X102 risers will fit the Burgman 650 but does require some rerouting of the control cables. 

QUESTION: Which risers will fit my 2003 Honda CB900F (919) Hornet. Can I use X102 without changing any lines? 
ANSWER: Our X102 risers will work on the 919 without any changes to the control cables. 

QUESTION: Will the universal risers fit my triumph thunderbird sport de 1998 without modification to cables? 
ANSWER: Our X102 and X103 style risers will both fit the 1998 Thunderbird sport. All of the stock control cables will work without modification. 

QUESTION: I'm looking @ the universal risers..1in. up and 1 3/8 in. back that fit 7/8 handlebars..I'm wondering about the center to center spacing of the bolts..I want to use these on my 1200 Suz. Bandit and the spacing is 1 3/8 in. center to center of the handlebar mounting bolts. 
ANSWER: Our X102 risers will fit the Bandit 1200. The up and back risers will require the longer brake hose that comes specifically for the Bandit. Our bolts hole spacing is 1 3/8". 

QUESTION: I HAVE AN 03 SV 1000, WILL i NEED ANY MODIFICATIONS TO CABLES ETC. 
ANSWER: No modifications to the control cables are necessary to install the risers.


QUESTION: question on the X102 universal riser: are the holes on the top of the riser (for the caps) on 35mm or 1 3/8" centers. My bike has a cap on top of the mount that I would like to put back on over the risers. 2010 Hyosung GT250 Naked. Thank you. Jeff. are the X102's in stock? 
ANSWER: The holes are 1 3/8" center to center. However, the rear holes are elongated to allow the risers to be installed on slightly different hole spacings. The X102 risers will fit 35mm bolt hole spacing. 

QUESTION: do you have any handerbar risers ffor the 2010 Triumph Thunderbird 1600cc model? Thank You in advance. Chris 
ANSWER: We currently do not offer a riser for the 2010 Triumph Thunderbird 1600. Sorry we couldn't help you out.


QUESTION: will the x102 risers fit an 85 night hawk 650 
ANSWER: Our X102 risers will fit the 85 nighthawk 650 without any changes to the control cables.


QUESTION: What would it cost for the flat bottom X102 in aluminum? Thanks, Wolf
Q:
I'm thinking of using your x102 on my Honda VTR1000. I am going to go with the superbike bars. If I mill off the radiused base and drill my upper triple clamp to mount the riser, will my control cables be long enough? Do you offer anything like a flatbottomed, stepped riser?
A:
We have not tried that application on a VTR1000 here at GenMar. We can make a set of the X102 risers with the bottom radius milled down for you. I think you would have enough slack in the stock cables but I can't say for certain. 
ANSWER: The cost would be the same as the X102 risers. We would just take a set that we have in stock and mill the bottom off for you. 

QUESTION: I have a 1984 virago 1000cc that we are doing some mods too. I want to upgrade handlebar from 7/8 dia. to 1" dia. will this work for me?
Gary 
ANSWER: The X102 risers will not adapt to use a 1" handlebar. 

QUESTION: HI,WILL THE X102 FIT A 2001 BMW R 1150 GS WITHOUT ANY CABLE MODIFICATIONS ? TANKS!ALSO HOW MUCH IS POSTAGE TO BRAZIL? 
ANSWER: Our X102 risers will fit the 1150 GS without cable modifications. 

QUESTION: I have a 1993 Suzuki VX800. Will this fit without any changes to the control cables? 
ANSWER: The X102 riseres will fit the VX800 without any changes to the control cables. 

QUESTION: do you make risers and reach backs for a 2003 hd deuce and a 2001 gs500e , If so will the lines have to be replaced? 
ANSWER: We currently do not offer risers for any of the Harley Davidson models. However, our X102 and X103 risers will both fit on the 2001 GS500 without any changes to the control cables. 

QUESTION: Are there any plans to offer a product to fit the new generation of Triumph Speed Triples that are coming stock with Magura "Fat Bars" now? I'm hoping to avoid the expense of switching out to 7/8" bars, clamps, etc.
Thank you for your time.
Emore 
ANSWER: Hi,
We do have plans to make risers for the new Speed Triples but it will be mid summer before we have a chance to get started on them.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hello,
do you have 25mm handlebar risers suitable for BMW R1200C? Thanks 
ANSWER: We currently do not carry a riser that will work on the R1200C. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will the risers fit a 2007 honda 919? Without modifications? Which model? is the 1" up and 1 3/8' the max? 
ANSWER: Hi,
Our X102 and X103 style risers will both fit on the 919 without any modifications. The X102 risers are the max for rise and pullback that we carry for the 919.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi, I have a 1999 Kawasaki Vulcan Nomad 1500, whill this fit?
Thank You, 
ANSWER: Hi,
Our X102 risers will not work on the 1999 Vulcan 1500. The 1500 has 1" bars and the X102s are for 7/8" handlebars. Only our K112 risers will work on this model.
Thank you,
ScottGenMar 

QUESTION: hi..do you have a riser kit for a 1991 gsx 750f,if so how high do they lift the bar and what mods are req'd to cables,pipes etc...thanks..andy 
ANSWER: Hi Andy,
We currently do not offer a riser for the GSX750F. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi there
please advise to hiddenaustralia@optusnet.com.au
please confirm the riseers will fit a 1995 XJ 900 diversion and please advise if there is any need to extend cables / have other cables installed.Please advise cost to ship/post to Brisbane Australia 
ANSWER: Hi,
The X102 risers will fit the 1995 XJ900 Diversion without any changes to the control cables.
Thank you,
ScottGenMar 

QUESTION: Will I need to get longer cables if I put this riser on the 09' Bonnie? Thanks!
Q: Will these fit on a 2009 Triumph Bonneville? Will I need to get longer cables?
A: Our X102 risers will not fit the 09 Bonneville. The bolt hole spacing is wider on the Bonneville. We do carry risers for the 09 Bonneville. They are our part # T112 and raise the bars up 1 1/4" and back about 5/8" due to the angle. The risers come in black.

ANSWER: You will not need longer cables to install the T112 risers on the 09 Bonneville.
Thank you,
ScottGenMar 

QUESTION: Will these fit on a 2009 Triumph Bonneville? Will I need to get longer cables? 
ANSWER: Hi,
Our X102 risers will not fit the 09 Bonneville. The bolt hole spacing is wider on the Bonneville. We do carry risers for the 09 Bonneville. They are our part # T112 and raise the bars up 1 1/4" and back about 5/8" due to the angle. The risers come in black.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will the handlebar risers fit a 2002 BMW r1150r? Will there be any modifications? If so are they a stock item? 
ANSWER: Hi,
Both or X102 and X103 risers will fit on the 2002 BMW R1150R without any changes to the control cables. Both items are currently in stock and ready to ship.
Thank you,
ScottGenMar 

QUESTION: Can the x102 riser be reversed safely as I want to move the bars up and forward on my trail bike (kl250)as they are too close when standing.Phil NZ 
ANSWER: Hi,
We have had many tall riders turn the X102 risers backwards. As long as they are installed properly, you will not have any problems.
Thank you,
ScottGenMar 

QUESTION: Hi two matters for two bikes
1. Virago 97 1100 I note above a comment about joining two risers together Do you have one which goes higher than the X102 which is only 1" higher or is it necessary to join two and if done does this interfere with handling at all and if two are joined how far back does this then bring the bars
2. Diversion 1995 XJ900. What would be the most suitable as a riser for this bike and again if required could you or would you join two risers for additional height 
ANSWER: Most customers go with the Y121 riser on the Diversion and rarely need to stack two sets of risers together. The Virago is a slightly different application. Because of the way the stock risers are shaped on the Virago, the risers do almost the opposite of what they were designed to do. They will raise the bars up 1 3/8" and get them back about 3/4". Although it is possible to stack two sets of our risers together, we recommend trying one set at a time first.
Thank you,
ScottGenmar 

QUESTION: Hello, will the X102B fit the 2002 ZRX1200. Thanks scot 
ANSWER: The X102B will fit the 2002 ZRX1200. You will need to reroute the throttle cable to get the slack you need.
Thank you,
ScottGenMar 

QUESTION: I'm looking to raise the bars on my 2008 Honda Rebel (without changing lines). I was looking at the 1" up and 1 3/8" back riser. 1.) will it fit? and 2.) can I flip them around to actually push the bars forward? Thank you for your time. 
ANSWER: Hi,
You can turn the risers around on the 2008 Rebel. However, the stock risers are shaped differently than our X102 risers and cosmetically do not match up very well. The risers will fit but will not look very good.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Ref X102 Riser: When fitting to 2009 Suzuki GS 500, do both screws go in from the top, i.e. it is not necessary to dismantle any part of the top plate between the fork legs. 
ANSWER: The risers mount directly where your bars are mounted now. Both mounting bolts go in to the tripleclamp from the top. It is not necessary to remove anything from the top tripleclamp to install the risers.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2007 honda 919 will the x102 fit ? thanks, mike 
ANSWER: Hi Mike,
The x102 risers will fit the 07 919 without any changes to the control cables.
Thank you,
ScottGenmar 

QUESTION: Scott, Will the X103 work on my 2004 TBird sport without having to change to longer cables? Please let me know ASAP. Thank You
Dave 
ANSWER: Hi Dave,
You will not have to change or reroute any of the cables on a 2004 TBird Sport when using the X103 risers.
Thanks for the inquiry,
ScottGenmar 

QUESTION: will the x102 risers fit the 2009 suzuki v strom 650 with abs without changes to cables and hoses 
ANSWER: The X102 risers will fit the 09 VStrom 650 ABS without any changes to the control cables.


QUESTION: I've got the Tag Metal risers for a 7/8 +5mm size handle bar. Will x102 work with my riser set up? 
ANSWER: Hi,
The X102 risers will not work with the Tag Metal oversize bars. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: hi
i have a triumph bonneville america. do you have handlebar risers to fit my bike? many thanks 
ANSWER: Hi,
We currently do not offer a riser that will fit correctly on the Bonneville America. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: will these work on my 06 kawasaki ZX10R? 
ANSWER: Our X102 risers will not work on the ZX10R. Sorry we couldn't help you out.
GenMar 

QUESTION: would these risers fit a 1991 gsx750f as im making it into a streetfighter and removed all fairing etc? 
ANSWER: Our X102 risers will not fit the 1991 GSX750F with stock handlebars.
Thank you,
ScottGenMar 

QUESTION: i have a 1993 honda cb 750 nighthawk is this product useable?.( X102B  Anodized Black Finish) geir from norway 
ANSWER: Hi,
The X102B risers work very well on the 750 Nighthawk. No changes to the control cables are necessary.
Thanks for the inquiry,
ScottGenMar 

QUESTION: What handlebar risers / setback for a 2003 Yamaha v star 650 
ANSWER: Hi,
Our Y122 risers will raise the bars up 1 1/2" and get the bars back just over 1" on the 2003 VStar 650.
Thank you,
scottgenmar 

QUESTION: Will the Item no. X102 fit my 1995 Ducati M900 monster? It looks like I have a 7/8" bar, will it hit the gas when I turn the handel bar? 
ANSWER: Hi,
The X102 risers will not work on the M900 Monster.
Thank you,
ScottGenMar 

QUESTION: I have 1997 honda cb 750 nighthawk is this product useable? Thx 
ANSWER: You can use the X102 style risers on the 750 nighthawk without any changes to the control cables. We carry them in black to match the bike.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2004 vstrom 650 wit stock handle bars, and was wondering if there is enough length in the cables to accommodate these risers? 
ANSWER: The X102 risers will fit the 04 VStrom 650 without any changes to the control cables.
Thank you,
ScottGenMar 

QUESTION: Will the universal risers fit my 2009 Bandit 1250s without modification to cables? 
ANSWER: Hi,
The X102 risers will fit the Bandit 1250 with no changes to the control cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi, What risers should I use on a 1999 Triumph Thunderbird Sport? 
ANSWER: Hi,
Our X102 and X103 risers will both fit the 99 Thunderbird Sport without any changes to the control cables.
Thank you,
ScottGenMar 

QUESTION: Will the x102b fit an '81 KZ750? Thanks 
ANSWER: Hi,
Our X102b risers will fit the 81 KZ750.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will these risers require cable extension for a VStrom 650 ABS version? 
ANSWER: Hi,
You will not need to change the brake hose on the VStrom 650 with ABS. There is just enough slack allow the risers to be installed without modification.
Thank you,
ScottGenmar 

QUESTION: Hi, will X102 fit my BMW R1200R Model 2006? I live in South Africa. What will it cost me in total to have it shipped to me? Thanks. Dennis 
ANSWER: Hi,
The X102 risers will not fit the 2006 R1200R. We currently do not offer a riser that will fit your bike. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2003 yamaha fz1. I don't see any Q & A on my specific model. Will the x102b work on my machine. Thanks 
ANSWER: Hi,
The X102b risers will fit the FZ1. However, you will need a longer brake line. The X104 risers are the only application we carry for the FZ1 that does not require any modifications.
Thank you,
ScottGenmar 

QUESTION: Will the X102 fit a 2004 R1150R without any cable modifications? 
ANSWER: The X102 risers will fit the 04 R1150R without any changes to the control cables. You may have to remove a ziptie but no changing or rerouting.
Thanks for the inquiry,
ScottGenmar 

QUESTION: hi i have a f650gs bmw and need bars up and back, will this product fit my bike? thanks neil 
ANSWER: Hi,
The X102 risers will fit the F650gs with 7/8" handlebars.
Thank you,
ScottGenmar 

QUESTION: Hi Scott: I have an '86 yamaha fj1200. Do you have risers for my aplication? If so what ,if any,mod will I need to make? thanks for all the info:)
chris 
ANSWER: Hi Chris,
Our Y117 risers are specifically made for the FJ1100/1200. There are no modifications to the bike necessary to install the risers.
Thank you,
ScottGenmar 

QUESTION: I have a 2008 Bandit SEA touring model. Does the S121a work for this version too? Thanks! Also, do you ship to Canada? 
ANSWER: Hi,
The S121a risers will fit on the SEA touring bandit 1250. We do ship to Canada daily.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi;
I am looking a handlebar raiser for my 2007 Suzuki SV650S (Halffaired racing version). Ýt this item compatible with my ride or which product do you offer me?
Thanx a lot 
ANSWER: Hi,
We only carry risers for the standard SV650 and don't have anything for the S model. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi I'm interested in your either your x102 or x103 product, as they fit 1991 XV1100 Virago. A number of questions: 1)Do the x103 risers come with their own caps, eg: is the x103 kit a total of 8 pieces, meaning, 2 bases, 2 caps, 4 bolts? 2) From the photgraphs,it appears the x102 kit is supplied with the same bolts as the x103....does the x102 kit come supplied with 2 center bolts longer than the others so that it bolts through into the existing riser base?
3)What are the sizes of the bolts supplied? 4)Could you stack two x103's together, or stack an x103 on an x102? Any info is helpful thanks. 
ANSWER: The X103 risers do come with caps, bases and 4 bolts. The X102 risers do come with long bolts in the middle that go through the entire riser and down into the triple clamp. It is possible to stack two sets of the X103 risers together or use an X103 stacked onto an X102.
Thank you,
ScottGenmar 

QUESTION: Hi,
Will the X102B risers work with a 2002 Yamaha FZ1? Thanks.

ANSWER: You can install the X102b risers on the FZ1. However, a longer brake hose will be needed.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi Further to fitting on a GSX650F (below)
1)Are any changes required to the control cables? 2)Can you please advise on shipping to the UK? Thanks Simon
QUESTION: Will the X102 risers fit an 08 Suzuki gsx650F? Thanks
ANSWER: Hi, The X102 risers will fit the 08 GSX650F. Thanks for the inquiry, ScottGenma 
ANSWER: You will not need to change any of the control cables. We do ship to the UK daily.
Thanks again,
ScottGenmar 

QUESTION: will the X102b work on a 1980 xs1100 without hitting the tank.thanks 
ANSWER: Our X102 risers will fit the XS1100 without any contact issues.
Thank you,
ScottGenmar 

QUESTION: Will this riser fit a 2007 ninja 650r? 
ANSWER: Hi,
Our X102 risers will not work on the 650r. Our K114 risers are specifically made for the 650r.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Will the X102 risers fit an 08 Suzuki gsx650F?
Thanks 
ANSWER: Hi,
The X102 risers will fit the 08 GSX650F.
Thanks for the inquiry,
ScottGenmar 

QUESTION: I have a 2007 Suzuki GS500F. Will the X 102 risers fit this bike?
Thanks 
ANSWER: Hi,
The X102 risers will fit on the GS500F.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi,you mention that your Y121 is the same as X102,so is it correct to say that if I were to order,the item would be X102.And does it comes with the fasterners?Pls advice,thanks
Regards

Your Question is:
Do you have handle bar riser for Yamaha xj900s diversion yr2003
Our Answer is:
Hi, Our Y121 risers are the same as the X102 risers but in a silver finish for the Diversion. The cost is the same as the X102s.

ANSWER: If you order the Y121 risers they will be the same dimensions as the X102 risers except in a sliver finish instead of brushed aluminum. All mounting hardware is included.
Thank you,
ScottGenmar 

QUESTION: Ihave a suzuki 2006 gsx750f.Iam told there is no one who makes them for that bike,would you know if there is something else that will do the job for me. 
ANSWER: You might look into a conversion kit that will allow you to use conventional type handlebars.
Thank you,
ScottGenmar 

QUESTION: will these risers work with a suzuki drz400 
ANSWER: The X102 risers will fit on the DRZ400 without any changes to the control cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Do you have handle bar riser for Yamaha xj900s diversion yr2003 
ANSWER: Hi,
Our Y121 risers are the same as the X102 risers but in a silver finish for the Diversion. The cost is the same as the X102s.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi,
can you confirm that there will be no cable problems with the X102 on a 97 Yamaha Diversion 900.Do you ship to UK
Thanks. 
ANSWER: Hi,
You will not have to change or reroute any of the control cables on the Diversion 900. We do ship to the UK daily.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will your risers fit on an '05 Bonneville America 
ANSWER: Hi,
Our X102 risers will not fit the Bonneville America. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Yes will these fit a 2009 F800GS? Thanks Kerry 
ANSWER: Hi Kerry,
We have not had a chance to try the X102 risers on the 09 F800GS. You might check back in 23 weeks.
Thank you,
ScottGenMar 

QUESTION: I want to buy a SV 1000 S, but I also want to raise the handlebars up and back. Will these risers work?
Thanks,
Cindy 
ANSWER: Hi Cindy,
We currently do not offer a riser for the SV1000S. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Scott, you said the x102 risers would fit a 2008 suzuki GSX650F. But is there
any brake or throttle line changing. Thanks Andy

ANSWER: Hi Andy,
You do not have to change the contol cables but you will need to remove them from any zipties or routing brackets to get the slack you need. It is a very simple modification.
Thank you,
ScottGenMar 

QUESTION: Hi ,can I purchase this style riser with this hieght and back gain for a bonneyville ? 
ANSWER: Hi,
We currently do not offer the up and back style riser for the bonneville. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Will the risers fit an 06 GS500f 
ANSWER: Hi,
Our X102 risers will fit the 06 GS 500.
Thanks for the inquiry,
ScottGenmar 

QUESTION: I need a riser for 2008 ninja ex650r a 1" or a 2" or some thing near to that thank's. 
ANSWER: Hi,
Our K114 risers will raise the bars up 1 1/4" on the 08 Ninja 650R without changing the control cables.
Thank you,
ScottGenMar 

QUESTION: Do you have a handlebar riser to suit a 1996 Suzuki 750F? If so how much are they  including shipping to Australia?
Thankyou, Bruce Hoffmann 
ANSWER: Hi,
We currently do not carry a riser for the 750F. Sorry we coudln't help you out.
Thank you,
ScottGenmar 

QUESTION: Will the X102 fit a 2006 Honda 919 without cable and or hose replacement? 
ANSWER: Hi,
The X102 risers will fit the 919 without any changes to the control cables. You may have to remove wire ties to get a little extra slack in the cables but no rerouting or replacing of the cables.
Thank you,
ScottGenmar 

QUESTION: will the x102 risers work for a 2004 honda 919/cb900f 
ANSWER: Hi,
The X102 risers will fit on the 04 919.
Thanks for the inquiry,
ScottGenmar 

QUESTION: I received email ref 1 inch riser #Y122 for a 2007 Yamaha VStar 650 classic, but also need a little pull back as well as rise. Please advise if your universal X102 will fit and not hit gas tank when fork is at full lock. 
ANSWER: The X102 risers will not work on the VStar. The Y122 risers will raise the bars up 1 1/2" and get them back 7/8".
Thank you,
ScottGenmar 

QUESTION: I have a 2008 Suzuki GSX650F. Which risers if any will fit? 
ANSWER: Both our X103 and X102 risers will fit the 08 GSX650F.
Thank you,
ScottGenmar 

QUESTION: Hi, I have a 2001 zr7s, I know the universal risers will work but do you also sell the extended brake lines? Thanks 
ANSWER: We do not carry the brake line for the ZR7S. Sorry.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi will these fit my Ducti S4R07 Monster 
ANSWER: Only our D100 risers will fit the 07 S4R.
Thank you,
ScottGenmar 

QUESTION: Hello  What barback risers do you offer that will fit my 1996 BMW K1100RS. I am hoping not to have to change any cabbles or the brake hose, but will consider ant risers that willfit this motorcycle. Thanks for any info! Kind Regards  Steve Kurylo Weare NH  USA 
ANSWER: We currently do not offer a riser for the K1100RS. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi Scott,
I would like to know if either the X102B or the X102 woill fit a 1989 Honda Hawk gt 650?? Thanks 
ANSWER: We currently do not offer a riser that will fit on the Honda Hawk. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Will the x102 fit a 2007 Honda VTX1300R? Will it hit the instrument cluster on the tank? Will cable changes be necessary? THX 
ANSWER: Hi,
The X102 risers will not fit the VTX1300R.
Thank you,
ScottGenMar 

QUESTION: I have a Suzuki 2007 1000 v strom.Will I need any new cables or hoses if I use your risers.also what risers will fit my bike.Thanks alot, 
ANSWER: You can use the X102 or X103 style risers on the VStrom 1000. Neither model will require that you reroute or change any of the control cables.
Thank you,
ScottGenMar 

QUESTION: I own a 2007 gsr 600 and i am not able to enjoy by bike as i feel the handle bars are beyond my reach,can u please help to have the handle bars at a reacheable distance for me.can u please provide me with pictures.thank you 
ANSWER: Hi,
We currently do not offer a riser for your bike. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: will the handle bar size 7/8" not hit the tank if move left or right if this UNIVERSAL RISERS 7/8" TUBE TYPE HANDLEBARS 1" UP & 1 3/8" BACK will install on yamaha dt 125cc? 
ANSWER: Hi,
The X102 risers will fit the Yamaha DT125 without hitting the tank at full lock.
Thank you,
scottgenmar 

QUESTION: Hi looking to put a set of these on a suzuki bandit. I beleive I need the part # S121a for this. Do you supple these? Also how much is postage to australia?
Thanks Rick 
ANSWER: 

QUESTION: will theese fit a honda st1100 1991 
ANSWER: Hi,
Only our X103 and X104 risers will fit the ST1100. The X102 style will just barely hit the tank and full lock.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Good day to you. I'm interested to know if your "universal risers" will fit a early 70's Moto Guzzi. It has 7/8" bars but I can't tell if the machined holes /spacing etc. will work.
Thanks in advance.
Regards,
Howard Burton 
ANSWER: Hi Howard,
The bolt hole spacing for our X102 risers is 1 3/8". The holes are slightly elongated to allow a small bit of flexibility with the spacing. We don't have any pre 1990 Guzzis on our computer. I apologize for the lack of information.
Thank you,
ScottGenmar 

QUESTION: Sorry, me again. I just asked a question re: KLX300R. I have now read above that there appears to be conflicting measurements given. In one reply you say that the bolt hole spacing for the X102 will fit a 32mm spacing, while in another you say the bolt hole spacing is 1 3/8, which according to me is closer to 35mm? Can you please clarify and let me know if these will fit on a KLX300R, as I'm pretty keen to order if they fit. Regards Stan. 
ANSWER: Hi Stan,
The bolt holes are elongated which is what makes them universal. Both measurements are correct because the bolts can be moved slightly to fit different bikes.
Thank you,
ScottGenMar 

QUESTION: Do your X101 risers fit a 2008 Bandit 1250S with ABS? and do I need longer brake lines? 
ANSWER: You will not need a longer brake line on the 08 Bandit 1250. The riser you need is part # S121a . It is the bandit risers without the brake line.
Thank you,
ScottGenmar 

QUESTION: will the x102 riser fit a 2007 bmw r1200r?m 
ANSWER: Hi,
The X103/X102 risers will fit on the 07 BMW r1200r.
Thank you,
ScottGenMar 

QUESTION: Hi Guys, I have a couple of questions. Will the X102 fit my Honda CB750 F2, circa 1978,without the need to buy extended brake hoses? Also, I cannot see the use of more than one allen screw, used on the lower fitting in the photo. Surely there are 2? Thanks. 
ANSWER: The X102 risers will fit on the 1978 CB750. Each riser will have two bolts fastening it to the tripleclamp.
Thank you,
ScottGenMar 

QUESTION: Will these risers fit a 2007 Triumph Scrambler 900? 
ANSWER: The bolt hole spacing on the scrambler is different than the X102 pattern and will not fit. 

QUESTION: I have a 1978 BMW R80. Will the X102 fit this bike? It looks correct based on your dimensions (ANSWER: The bolt hole spacing is 1 3/8" and the bolts are 8mm with a 1.25 thread pitch. Thank you, ScottGenMar) How long are the bolts. 
ANSWER: Hi,
The X102 risers will fit the 78 BMW R80.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hello will the X102 fit a 76 KZ900 with 7/8" handlebars? 
ANSWER: The X102 risers will fit the 1976 KZ900.
Thank you,
scottgenMar 

QUESTION: X102...will these risers work on a Honda XR650L in a up and FORWARD positioning of the handlebars??? TIA 
ANSWER: We typically don't install them in a forward position. If you have 1 3/8" clearance forward the X102s will work.
Thank you,
ScottGenMar 

QUESTION: Hello. I need handlebar risers for my Triumph
Daytona 04 955i. Do you have any that will fit my model? Please advice.

ANSWER: Hi,
We currently do not offer a riser for the 955i. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will the x102 work on a 2000 R1? 
ANSWER: Hi,
Our X102 risers will not work on the R1.
Thank you,
ScottGenMar 

QUESTION: hi, i have a 82 honda cb900c and was wondering if you could tell me if the universal riser (1" up and 1 3/8" back) would work on it? my mounting bolts are approximately 32mm on center and it has 7/8 handlebars. i would really love to know the center to center measurements on your risers to aid me in making my decision. thanks for any help, sincerely mark9hi, i have a 82 honda cb900c and was wondering if you could tell me if the universal riser (1" up and 1 3/8" back) would work on it? my mounting bolts are approximately 32mm on center and it has 7/8 handlebars. i would really love to know the center to center measurements on your risers to aid me in making my decision. thanks for any help, sincerely mark 
ANSWER: Hi,
The bolt hole spacing for our X102 risers is 32mm. They will fit your CB900C with 7/8" handlebars.
Thank you,
ScottGenMar 

QUESTION: Will these fit on a Kawasaki Z750S? 
ANSWER: Hi,
Only our K100 risers will fit the Z750S. The X102 risers are for 7/8" handlebars.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Is the middle bolt on the handle bar risers long enough to screw into the back hole on the original handle bar mount? From the photograph it did not appear to, but from a security point of view I thought it would. Regards, Greg

ANSWER: Hi Greg,
The middle bolt does go through the riser and into your top tripleclamp. You will have 4 bolts mounting the risers securely to the bike.
Thank you,
ScottGenMar 

QUESTION: Q: WILL THE UNIVERSAL RISERS 1"UP&1 3/8"BACK FIT MY 2006 FZ6?
A: The X102 risers will fit on the FZ6 but you will have to install a longer brake hose.
WHICH BRAKE HOSE WOULD YOU RECOMEND AND HOW MUCH DOES IT COST? 
ANSWER: We currently do not offer the required brake hose for the FZ6. You will need a hose the stock length plus 2".
Thanks again,
Scottgenmar 

QUESTION: WILL THE UNIVERSAL RISERS 1"UP&1 3/8"BACK FIT MY 2006 FZ6?

ANSWER: Hi,
The X102 risers will fit on the FZ6 but you will have to install a longer brake hose.
Thank you,
ScottGenmar 

QUESTION: I have a 2004 BMW R1200CLC. Will these risers fit it? 
ANSWER: Hi,
Our risers will not work on the 04 R1200CLC. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Can you advise if the risers will fit a Year 2001 BMW R 1100RT.
Thanks 
ANSWER: Hi,
We currently do not offer a riser that will work on the 01 R1100RT. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2001 ZX7R and as mentioned in a previous question can not locate the picture of a zx7r with the installed riser. I looked under the www.genmarmfg.com universal riser section. I am very interested in this product.
Thank you for your time. 
ANSWER: Hi,
We currently do not offer a riser for the ZX7R only the ZR7. Sorry we couldn't help you out.
Thank you,
ScottGenMar 

QUESTION: Can you tell me if the X102 will fit my 2001 fz1 and does the kit come with the front brake hose? 
ANSWER: Hi,
The X102 risers will fit the 01 FZ1. However, you will need to install a longer brake hose that we do not supply with the risers.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Do you know if your upandback risers will work on a 2007 BMW R1200GS?

ANSWER: Hi,
Our X102 risers will not work on the 07 R1200GS. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2007 fz1. I see above how you told someone with a 2006 fz1 that they need a longer brake cable. What about the clutch cable? Also,
where do you get the cable(s and how much do they cost? Thanks

ANSWER: You will only need to change the brake hose when putting the X102s on the FZ1. There is enough slack in the clutch. We get our brake hoses from Galfer Brakes and the cost vary depending on what you want.
Thanks for the inquiry,
ScottGenmar 

QUESTION: My bike is a 1984 K100RS, not K110RS. Does this work? 
ANSWER: Hi,
Our X102 risers will not work on the K100RS.
Thanks again,
ScottGenMar 

QUESTION: Will these fit a 1984 BMW K110RS?

ANSWER: Hi,
We currently do not offer a riser for the K110RS. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Will these fit my 1993 R100GSPD? 
ANSWER: Hi,
Our computer files do not list the R100GSPD. If your bike has 7/8" diameter handlebars and the bolt spacing on the handlebar clamps is 1 3/8", then they should work. Sorry we don't have more information for you.
Thanks for the inquiry,
ScottGenMar 

QUESTION: 2006 GS500f Suzuki, which riser model is it? 
ANSWER: Hi,
You can put either the X102 or X103 risers on the GS500.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will the X102 risers fit a 2001 Bandit 600? I already have a longer brake so I don't need the S121 model. 
ANSWER: Hi,
You can order the S121 risers without the brake line. The risers without the line are just our part # S121a. They are the same cost as the X102 risers but are sliver to match the bike.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I HAVE A 2003 CB750 NIGHTHAWK AND WONDER IF YOUR RISERS WILL WORK WITHOUT CABLE CHANGES. 
ANSWER: Hi,
The X102 risers will fit on the 03 Nighthawk without any changes to the control cables necessary.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will you be able to provide a 1" up 1 3/8 back, handle bar lift for a, 2006 Yamaha Stratoliner.
1900 cc. I have been getting bad neck pain on even short rides. Thankyou Ed. 
ANSWER: Hi Ed,
We only offer the Y127 risers for the Stratoliner. They will raise the bars up 1 1/4" and back about 3/4" due to the angle. This is currently the only riser we offer for the Stratoliner.
Thanks for the inquiry,
ScottGenMar 

QUESTION: hi would you have risers for my yzf 1000 yamaha 1996 model.if you dont could you ged me a pair and how much.thanks mark. 
ANSWER: Hi,
We currently do not offer risers for the YZF1000. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have CR Pro Taper bars on my 2003 DL1000. Do you make a riser similar to the X102 that will accept 1" bars? Thanks. 
ANSWER: Hi,
We currently do not offer a riser that is compatible with Pro Taper bars. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi Scott. I have a 2006 Yamaha FZ1. Will the riser Item no. X102 fit my bike with out a differant brakeline? I am also going to lower the bike 1 inch front and rear. Thank you. Brian. 
ANSWER: Hi Brian,
You will need a longer brake line to use the X102s on your FZ1. I'm not sure if lowering the front 1" will help you out with the slack.
Thank you,
ScottGenMar 

QUESTION: Will this item work on a 2007 suzuki c90T 
ANSWER: Hi,
The X102 risers will not work on the C90. The C90 has 1" bars and the X102s are for 7/8".
Thanks for the inquiry,
ScottGenMar 

QUESTION: I've been looking for a riser that would allow me to put a sporter bar on a 2002 buell blast. The turning radius is too small if I just replace the stock bar right now with the flater sporter handlebar. I was hoping using a riser would improve the turning radius. Do you think this would work? 
ANSWER: Hi,
A riser would give you the extra clearance you would need. However, we currently do not offer a riser for the Buell Blast. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGEnmar 

QUESTION: Will it fit a 1992 Yamaha Seca II? Nothing like it mentioned previous. Thanks Scott 
ANSWER: Hi,
The X102 risers will fit on the 92 Yamaha Seca II. No changes to the control cables are required.
Thank you,
ScottGenMar 

QUESTION: Hi, my name is oscar from Chile, i need this product to kawasaki kx 65 2003, do you have, many thanks 
ANSWER: Hi,
We do have the X102s in stock and they will fit on the 03 Kawasaki KX 65.
Thank you,
ScottGenMar 

QUESTION: will your risers work on a susuki c 90 street bike 
ANSWER: The X102 risers will not work on the C90. We have bike specific risers for the C90 part # S130. The S130s will raise the bars up 1 1/2" and back just over 1" due to the angle.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi there, I assume the risers will work on a BMW R1150 Rockster. Does installation requires any rerouting of cables/wires?
thanks, Manlio 
ANSWER: Hi Manlio,
Our X102 risers will fit on the R1150. There are no changes to the control cables necessary.
Thank you,
ScottGEnMar 

QUESTION: Hello! Will the X102 risers fit the 2006 Triumph Tiger 955i without cable changes? 
ANSWER: Hi,
The X102s will fit the tiger without any changes to the control cables.
Thank you,
ScottGenMar 

QUESTION: Will the X102 work for an 07 FZ1 as well? 
ANSWER: Hi,
The X102 risers will fit on the 07 FZ1 but you will have to lengthen the front brake hose.
Thanks,
ScottGenMar 

QUESTION: I understand the x102 will fit the 07 Sv650 suzuki but can you lift the gas tank for service? 
ANSWER: Hi,
You will have to remove the risers to raise the gas tank to its full height. You can access the filter but you cannot extend the tank fully without it hitting the risers.
Thanks for the inquiry,
ScottGEnMar 

QUESTION: do these risers fit a 1996 ninja 250? 
ANSWER: Hi,
The X102 risers will not fit on the 96 Ninja 250. Our K108 risers are specifically made for the Ninja 250.
Thank you,
ScottGenMar 

QUESTION: Will these risers fit a 2003 BMW R1200C? Will I need to replace cables, etc.? Thanks

ANSWER: Hi,
We currently do not offer a riser that will work on the R1200C. Sorry we couldn't help you out.
Thank you,
ScottGenMar 

QUESTION: Do your X101 risers fit a 2007 Bandit 1250? If so do I need longer brake lines as previous year models?

ANSWER: Hi,
The S121 or the X102 risers will fit the 07 Bandit 1250 without having to change the brake line.
Thanks for the inquiry,
ScottGenMar 

QUESTION: would these risers work on a 2005 vstar 1100 custom? 
ANSWER: The X102 risers will not work on the VStar. The X102 risers are for 7/8" bars and the VStar has 1" bars.
Thanks for the inquiry,
ScottGenMar 

QUESTION: do you have any risers that would fit the 06 Breva 1100. They would be similar to some of the Triumph risers. Thanks 
ANSWER: Hi,
Our X103 and X102 risers will fit the 06 Breva 1100.
Thank you,
Scott 

QUESTION: Hi are you offering free shipping to Quebec City, Canada G1P 2R9. If not how much?
Tks 
ANSWER: Hi,
Shipping to Canada is $8.00 for global priority which usually takes around 57 days to arrive.
Thank you,
ScottGenMar 

QUESTION: I want the 1 inch up and back risers for my 2007 SV650. It has manifold front brake lines and does not appear to have enough slack for risers. How do I effect the modification? 
ANSWER: The brake line has a bracket on the bottom tripleclamp. The bolt holding the bracket can be removed to get the extra slack you will need.
Thank you,
ScottGenMar 

QUESTION: I have a 2006 Suzuki DL 1000. I am interested in the X102 Handlebar Riser. What is the width of the riser. Also, the base plate for the stock riser has a slight radius to it...will the X102 Riser match that Radius? Thanks, Bob 
ANSWER: Hi Bob,
The width of the X102 risers is 21mm. The radius on the risers does match the stock radius on the DL1000.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have the 1979 kz650 i was wondering are there any other kits you have that will bring my bars up and back further than this set?
thanks again

ANSWER: The X102 risers are the only risers we carry for the KZ650 that would bring the bars up and back.
Thank you,
ScottGenmar 

QUESTION: i have a 1979 kz650 will this work for my bike? 
ANSWER: Yes, the X102 risers will work on a 79 KZ650.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2005 suzuki boulevard M50, please tell me these will fit my bike. I am another one of those 5 foot nothing wives. If so which ones? 
ANSWER: Hi,
We currently do not carry a riser for the M50. It is going to be tough to make a riser work on the M50 with its speedometer setup.
Thank you,
ScottGenMar 

QUESTION: Dear Sir,
A question about the x102 universal riser (Bar) Is the listed price for one unit only?
Obviously two are required. I just want to be sure before ordering.Thank you
Regards Philip..(New Zealand)

ANSWER: Hi Philip,
The price listed is for a full set of two risers and mounting hardware.
Thank you,
ScottGenMar 

QUESTION: Looking for a product like the x101 or x102 for a 2006 Harley Heritage SoftailFLSTC!! Do you carry anything?? 
ANSWER: Hi,
We currently do not carry any risers compatible with the Harley models. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will this set fit my 1985 BMW k100rs 
ANSWER: Hi,
The X102 risers will fit the 85 BMWK100RS.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Sorry if this is redundant for the 85 Nighthawk, but i do not know if there are differences in the handlebar configuration: I have an 86 Nighthawk CB700SC......
Thanks,
Andy 
ANSWER: Hi Andy,
The X102s will fit on the 85 nighthawk CB700SC without any changes to the control cables.
Thank you,
ScottGenMar 

QUESTION: I have a 2005 Victory V92 Touring cruiser. After installing a different seat, it set me back about one inch further from the bars. Do you make setbacks appropriate for my bike and if so, are there any peculiar installation issues? Thanks.

ANSWER: Hi,
We currently do not carry a riser for the Victory models. The bolt hole spacing is different on the Victory than on the metric models. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I would just like to confirm that the X101 will fit a 2000 Bandit 1200? And what are the shipping costs to Nova Scotia Canada? 
ANSWER: Hi,
The X101 will fit the Bandit. However, you will need a longer brake hose to accommodate for the risers. We typically send our part # S121 that comes with longer brake line for the bandit models. Shipping to Nova Scotia is $10.00.
Thank you,
ScottGenMar 

QUESTION: have a 1990 fj 1200 I would like to raise the handle bars can you
please make a suggestion on product.
Thanks 
ANSWER: Hi,
Our risers for the 1990 FJ1200 are our part # Y117.
Thank you,
ScottGenMar 

QUESTION: HELLO..WILL THE X102 FIT A 2001 KAWASAKI ZRX 1200R THANKS ...RICHIE 
ANSWER: Hi Richie,
The X102Bs will fit the 01 ZRX1200. You will only need to reroute the throttle cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I see where you said the X102 will fit the VMAX but what about cable length? every thing OK there? By the way I made a set of what I called Barbacks for my 1980 Yamaha 850 Midnight Special back in 1980 before There were any available commericialy and they looked excactly like your X102s' But I'm retired now so I guess I'll just buy a set. 
ANSWER: Our X102s will fit the VMAX without any cable changes. Also check out our part # Y124 that is bike specific for the VMAX.
Thank you,
ScottGenMar 

QUESTION: Will the x102b fit my 2000 honda nighthawk 750 without relocating any control cables or wires?
thanks! 
ANSWER: Hi,
The X102B will fit the 2000 Honda Nighthawk 750 without any modifications to the control cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi do you have risers for a 1996 GS500E with clipon bars? Thanks, Matthew 
ANSWER: Hi Matthew,
We do not carry any risers for clipon type bars that are mounted below the top tripleclamps. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Hi
Do you have any images showing the X101 or X102 installed on a 0307 SV650 naked? Any chance you could do Priority mail to Honolulu? Aloha! 
ANSWER: Check out www.genmarmfg.com under the SV650 link and there is a picture of the X102s installed on a SV650 naked. We would be happy to ship Priority mail to Honolulu.
Thanks for the inquiry,
ScottGenMar 

QUESTION: hi i was wondering if these risers would work on 2003 zx6r 
ANSWER: Hi,
The X102 risers will not work on the ZX6R. We currently do not offer a riser for the ZX6R. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: wll your risers fit my suzuki gsr600
derrick 
ANSWER: Hi Derrick,
We currently do not have a riser for the GSXR600. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: 1984 BMW R100CS, actually any R100 or R90 from '80 to '84. Aslo, why do you not list exact dimensions ( hole spacing, bolt size and so on )? 
ANSWER: The bolt hole spacing is 1 3/8" and the bolts are 8mm with a 1.25 thread pitch.
Thank you,
ScottGenMar 

QUESTION: i have a 2003 suzuki sv650s, which ones do i need 
ANSWER: Hi,
We currently do not carry a riser for the S model. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: I have a 2000 BMW R1200C will your risers fit that bike if so which riser model. 
ANSWER: We currently do not have a riser available for the R1200C. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: I see that the front bolt is there, but is there a longer bolt in the middle that goes through to attach to the rear hole of the stock clamp? 
ANSWER: Hi,
The middle bolt does go all the way through. There are 4 bolts mounting the X102s to the tripleclamps.
Thank you,
ScottGenMar 

QUESTION: Will either X101 or X102 fit my 98' R1100GS without rerouting cables? Thx... 
ANSWER: Hi,
Our universal will not fit on the R1100GS. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a BMW R1200C...will either of these fit...exactly what I am looking for. 
ANSWER: Hi,
Our universal risers will not fit the R1200C. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenmar 

QUESTION: i have a 1998 triumph adventurer will the x102 fit without any rerouting of cables or tank issues? 
ANSWER: Hi,
The X102s will fit the Adventurer without any changes to the control cables.
Thank you,
ScottGenmar 

QUESTION: Will these risers fit a 2003 Triumph Thunderbird Sport? I am at the point where I experience pain after 30 minutes. I have read I can simply replace the Sport bars for the standard bars from the Thunderbird. Your advice please. 
ANSWER: Hi,
The X102 risers will fit the 03 Thunderbird Sport without any changes to the control cables required. It will be an easier and less expensive alternative to switching the handlebars. If the risers do not work, we have a 30 day money back guarantee.
Thank you,
Scottgenmar 

QUESTION: I'm looking for a riser that will raise my DL650 Vstrom bars up 2 Inches and back 1 inch. Any suggestions? thank you 
ANSWER: Hi,
We currently only carry the X102 risers for the VStroms. They will raise the bars up 1" and back 1 3/8". The X102s are currently the largest riser we have for the VStrom.
Thank you,
ScottGenMar 

QUESTION: I have a 1986 BMW R80RT. Bolt spacing is 33mm for the stock risers, what is the bolt spacing on your risers. 
ANSWER: Hi,
The bolt holes on the X102 risers are slightly elongated and will fit 33mm bolt hole spacings.
Thank you,
ScottGenMar 

QUESTION: I have brand new Moto Morini Corsaro 1200, will any of risers fit. 
ANSWER: Hi,
We currently do not carry a riser that will fit the Corsaro 1200.
Thank you,
ScottGenMar 

QUESTION: I have a bonneville t100 (2006)
with 1" dia. bars. I'm in dire need
of setbacks (1" up and 13/8" back).
Can your 7/8" setbacks
be modified for 1" dia.? If not
will you have a 1" version soon" 
ANSWER: Hi,
The X102 risers are not compatible with the 1" bolt hole spacing. We currently only offer the T114 risers for the Bonneville.
Thank you,
ScottGenMar 

QUESTION: I have a 1989 K100RS BMW. I would like to raise the handlebars 3 inches and the footpegs lowered 4 inches and maybe forward. Does your company have solutions? Thanks George from Alaska.

ANSWER: Hi George,
We currently do not offer a product to lower the pegs on the K100RS and our risers would only raise the bars up 1". Sorry we couldn't help you out.
Thank you,
ScottGenMar 

QUESTION: will this work on the new 2007 DUCATI GT 1000 ? or
Which riser will work ? Thanks 
ANSWER: Hi,
We haven't had a chance to try our risers on the 07 GT1000. We are having problems finding that bike in our area. You might check back in a couple weeks. Hopefully we will have some information for you then.
Thank you,
ScottGenMar 

QUESTION: For the 2006 Yamaha FZ6, will I need to change out any cables or controls? 
ANSWER: The brake line gets a little tight using the X102 risers on the FZ6. It isn't overly tight, but some customers do chose to change it out. The other cables are fine.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Hi, Will these risers, X102 work on my wifes Ducati monster 620. Shes 4 foot nothing and need all the help she can get. Thanks, Keith Smith
Charleston, SC 
ANSWER: Hi,
The X102s will fit on the Monsters up the 02 model. They will not fit on the 03 to current Monsters due to a change in the bolt hole spacing.
Thank you,
ScottGenMar 

QUESTION: Is there any chance these will fit a Yamaha WR450 F  this design is exactly what I'm looking for.
Keith 
ANSWER: Hi keith,
The X102 risers will fit the Yamaha WR450. You will not have to reroute or lengthen any of the control cables. A bunch of the local desert race guys have these on their bikes.
Thank you,
ScottGenMar 

QUESTION: I have a Moto Guzzi California Jackal which had normal 7/8" bars. When ordering a new one I was sent 1 1/4" bars. They couldn't provide me with new risers or 7/8" bars so I'm currently stuck.
Your universal bars look as though they would solve the problem. Can you please confirm.
Regards
Bill 
ANSWER: Hi Bill,
Our universal risers will not fit the Guzzi bolt pattern. We currently do not have a riser that will work on the Jackal. Sorry we couldn't help you out.
Thank you,
ScottGenMar 

QUESTION: Hi, I have a 2003 SV650 naked. Will the X102 and X101 both fit without any cable modifications? Also do you ship to the UK (London)? Many thanks. 
ANSWER: Hi,
The X102 and X101 risers are the same part now. The X102s will fit on the 03 SV650 without any changes to the control cables. We do ship to the UK daily.
Thank you,
ScottGenMar 

QUESTION: Which product will fit a 1992 Yamaha Virago 1100.
Thanks
John 
ANSWER: Hi John,
Our X103 and X102 risers will both work on the Virago.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Since you don't carry risers/higher clipons for the '05 SV650S, can you recommend a competing provider or manufacturer? Thanks much.
Terry 
ANSWER: Hi Terry,
You should check with Helibars or Cycle Cat.
Thank you,
ScottGenMar 

QUESTION: Hi, I see x102 risers installed on 2002 gs500. Does this app require any rerouting etc. or plug and play. Thanks, Steve 
ANSWER: Hi Steve,
You will not have to reroute any of the cables but you will have to remove some zipties to get the slack you will need.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2003 Suzuki SV1000, naked version, do you have any handlebar risers for this model. 
ANSWER: Our X102 and X103 risers will both fit on the 03 SV1000. You will not need to change or reroute any of the control cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Greetings, I am working on a 2005 FZ6 (Fazer). Will your RiserX102 work? they want up and back both. thanks bob Day, Calypso Cycle, Cottonwood Ca. 
ANSWER: Hi Bob,
You can put the X102s on the FZ6. The X102s will use most of the slack in the front brake line and some customers prefer a longer line installed.
Thanks for the inquiry,
ScottGenmar 

QUESTION: Will the X102 fit a 2006 FX6? 
ANSWER: Hi,
I'm not familiar with the FX6. What brand of bike is it?
Thank you,
ScottGenmar 

QUESTION: which part number do i order for a 2002 ZR7S 
ANSWER: Hi,
You can put the X103 or the X102 risers on the ZR7S. However, the front brake line will have to be lengthened when using either model.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Do you offer this for 1 inch bars? For a 2003 Victory V92CCD or a Universal set up in 1 inch 
ANSWER: Hi,
We currently do not offer the up and back riser for 1" bars. With most of the larger cruisers going with the 1" bars, we should have something in the near future.
Thanks for the inquiry,
ScottGenMar 

QUESTION:
Item no. X102
will this fit a 03 America?.... 
ANSWER: Hi,
Our X102 risers will not fit the 03 Bonneville America. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: will the x102b fit a 1985 Honda Nighthawk 650? 
ANSWER: Hi,
The X102B will fit the Nighthawk 650 without any changes to the control cables.
Thank you,
ScottGenmar 

QUESTION: hi i am very interested in buying some handlebar risers for my triumph thunderbird 2002 will the x102 risers fit my bike with out any cable or electric mods 
ANSWER: Hi,
The X102s will fit on the Thunderbird without any changes to the control cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Can you please tell me if the X102 risers will fit my GSX1400 K2? If so can I have the price including shipping to Scotland in the UK.
Yours Hopefully
Ian Graham 
ANSWER: Hi Ian,
The X102 risers will fit on the GSX1400 K2. The risers are $109.95 plus $9.00 for shipping to the UK.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Are there handle bar riser extensions for a 2001 Suzuki SV650S model? Please provide part number. Thanks, Greg 
ANSWER: Hi Greg,
We currently do not carry risers for the S model. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: HI ..WILL THE X102 FIT YAMAHA VMAX..? IF SO I WILL TAKE A SET..GARY 
ANSWER: Hi,
The X102 will fit the VMAX.
Thank you,
SW 

QUESTION: Will the X102 fit a 2005 Honda 919 without cable and or hose replacement? Thanks in advance.
Hank.

ANSWER: Hi Hank,
The X102 will fit on the 919 without any modifications.
Thank you,
ScottGenMar 

QUESTION: Looking for risers for a 2005 gsxr 600.
thanks.
kevin 
ANSWER: Hi Kevin,
We currently do not carry a riser for the 05 GSXR 600. Sorry we coulnd't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: This weekend I fitted the X101 riser on my Suzuki SV650. You're right...installation was easy and my riding position is much improved. Thanks for a great product! 
ANSWER: We appreciate the positive feedback.
Thank you,
ScottGenmar 

QUESTION: Will the X101 fit on a 2005 Suzuki SV650 (naked) without the longer brake hose? Thanks.... 
ANSWER: Hi,
The X102/X101 risers will fit on the 05 SV650 without any changes to the control cables necessary.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have 2005 Suzuki sv650S is this product useable? Thx 
ANSWER: Hi,
You will not be able to use the X102 on the SV650S. We currently only carry risers for the naked SV650 standard. Sorry we couldn't help you out.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will the X101 fit a 2004 Suzuki Bandit 1200 
ANSWER: The X101 risers will fit on the Bandit but it will require the brake line. Our S121 risers are made specifically for the Bandits. The S121s are silver to match the Bandit tripleclamp and come with the necessary brake hose.
Thanks for the inquiry,
ScottGenmar 

QUESTION: i have a 2004 thunderbird sport. i want to raise the bars an inch but do not want them back 1 3/8" (i think the bars may hit the tank with X102). do you have any risers that fit my bolt pattern? 
ANSWER: Hi,
Our X103 risers will raise the bar on the Thunderbird Sport up 1" and get them back only about 1/2" due to the angle of the stock risers.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Will X102 (the up&back risers) fit my 2004 SV650 Naked bike? Cable changes are necessary maybe? Thanks man! 
ANSWER: Hi,
The X102 risers will fit on the 04 SV650 without any changes to the control cables.
Thanks for the inquiry,
ScottGenMar 

QUESTION: Do you have any handlebar risers, similar to the Speed Triple riser, for the Speed Four? Thanks. 
ANSWER: Hi,
We should have our new risers for the Speed Four ready for sale in about 3 weeks. You might check back with us then.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a 2000 ZX7R and I am wondering if you have any pictures of this application in place. I am still confused as to how my clamp on handle bars will fit this configuration. Please advise and thank you. 
ANSWER: Hi,
We do have pictures of the risers installed on our web site at www.genmarmfg.com . Look under the universal riser heading on the top left corner of our home page.
Thanks for the inquiry,
ScottGenMar 

QUESTION: I have a Triumph 2003 Daytona 955i, I'm looking for frame sliders, and clipon handlebar risers. Do you have anything for this bike? Thanks 
ANSWER: We currently do not have anything for the Daytona 955i.
Thank You,
BruceGenmar 



Ask your question here: 

Your email (so we can send you the answer): 


